Editverse Free Calculator

Sigma Metrics Calculator (Westgard Six Sigma)

Judge an analytical method’s quality on the Six Sigma scale — the sigma metric from allowable total error, bias, and imprecision — with the exact R command behind the result. A full guide follows below. Validated against R 4.3.3.

In Simple Words

The sigma metric places a laboratory assay on the Six Sigma quality scale. It is calculated from three things: the allowable total error (the quality the test needs for its clinical use), the method’s bias, and its imprecision (CV). The formula is (allowable total error − bias) divided by the CV.

On this scale, a sigma of 6 is world-class and a sigma below 3 is generally considered unacceptable for patient testing. The metric lets a laboratory benchmark methods on a common scale and decide how much statistical quality control each method actually needs — high-sigma methods need fewer control rules than fragile, low-sigma ones.

When to Use Sigma Metrics

Use sigma metrics to evaluate analytical performance, benchmark instruments and assays, and design risk-based quality control. They translate abstract bias and imprecision figures into a single, decision-ready quality number tied to the clinical requirement.

The metric is only as good as its inputs: the allowable total error must reflect the test’s clinical purpose, and bias and CV must come from sound verification data. Use the sigma value to choose control strategy and to flag methods needing improvement. For the underlying measurement spread, see measurement uncertainty. Unsure how to set quality goals? Our Test Selector can help.

Westgard Sigma Metrics QC planning and sigma calculation · validated vs R 4.3.3
User guide

When to use. Compute the sigma metric for a laboratory assay and select appropriate QC rules.

Assumptions. TEa, bias and CV are in the same percentage units.

Common mistakes. Sigma below 3 requires intensive multi-rule QC; do not run with single rules.

Worked example

Click Load example data above, then Run Analysis to see a fully worked result with figure, formula and interpretation for this test.

References
  1. Westgard JO. Basic QC Practices. 4th ed. 2016.

Worked Examples

Example 1 — A strong method

A method has an allowable total error of 10%, a bias of 1%, and a CV of 1.5%. Sigma = (10 − 1) / 1.5 = 6.0 — world-class performance that needs only minimal statistical quality control to stay in spec.

Example 2 — A fragile method

Another method with the same 10% allowable total error but a bias of 2% and a CV of 3% gives sigma = (10 − 2) / 3 ≈ 2.7. Below 3 sigma, this method requires extensive control rules and frequent monitoring, and is a candidate for improvement or replacement.

Assumptions to Check

An appropriate allowable total error. The quality requirement must reflect the test’s clinical use; an arbitrary target makes the sigma value meaningless.

Bias and CV in the same units as the goal. All three inputs must be expressed consistently (typically as percentages) and come from reliable verification or quality-control data.

Stable, representative estimates. Bias from comparison or proficiency testing and CV from adequate replication should represent routine performance, not a best-case run.

Common Mistakes

Using an arbitrary allowable total error

The sigma value is only as meaningful as the quality requirement behind it. Base the allowable total error on biological variation, regulatory limits, or clinical need.

Mixing units for bias and CV

Bias and imprecision must be on the same scale as the allowable total error; mixing absolute and percentage figures corrupts the calculation.

Trusting a single short precision study

A CV from one small run underestimates routine imprecision. Use long-term quality-control data for a realistic sigma.

Treating sigma as the whole quality picture

Sigma summarises analytical quality against one goal; it does not capture pre-analytical errors or clinical interpretation, which also matter.

Frequently Asked Questions

How is the sigma metric calculated?

Sigma = (allowable total error − bias) / CV, with all three on the same scale, usually percentages.

What sigma value is acceptable?

Six sigma is world-class and below three is generally unacceptable for patient testing; higher sigma methods need less intensive quality control.

Where does the allowable total error come from?

From the clinical quality requirement — biological variation, regulatory criteria such as proficiency-testing limits, or expert consensus for the measurand.

Does the result match Westgard tools?

Yes. The calculator uses the standard sigma-metric formula and shows the R command so you can reproduce the value used in Westgard quality design.

References

  1. Westgard S, Bayat H, Westgard JO. Analytical Sigma metrics: a review of Six Sigma implementation tools for medical laboratories. Biochem Med (Zagreb). 2018;28(2):020502. PMID 30022879.
  2. Westgard JO, Westgard SA. Six Sigma quality management system and design of risk-based statistical quality control. Clin Lab Med. 2017;37(1):85–96. PMID 28153372.
  3. Westgard JO. Basic QC Practices. 4th ed. Madison, WI: Westgard QC; 2016.

Need This Analysis Done for Your Manuscript?

Our team supports analytical quality programmes — sigma-metric benchmarking, risk-based quality-control design, and bias and imprecision verification — with reproducible R output.

Get Expert Statistical Help