Editverse Free Calculator
Limit of Detection & LoQ Calculator (LoB, LoD, LoQ)
Determine the smallest concentration an assay can reliably detect and quantify: limit of blank and limit of detection from the parametric formulas described by Armbruster and Pry for a single low-level sample, a CV-based check of the limit of quantitation, or the ICH Q2 calibration-curve route, with the exact R command behind the result. A full guide follows below. Validated against R 4.3.3.
In Simple Words
Three related limits describe the low end of an assay. The limit of blank (LoB) is the highest signal a blank sample is likely to produce. The limit of detection (LoD) is the lowest concentration reliably distinguished from a blank. The limit of quantitation (LoQ) is the lowest concentration that can be measured with acceptable precision and accuracy.
They build on each other: LoB comes from measuring blanks, LoD from LoB plus the variability of low-concentration samples, and LoQ from the requirement that imprecision (and bias) stay within a stated goal. Reporting all three makes clear where an assay merely detects an analyte versus where it can quantify it dependably.
When to Use LoD and LoQ
Determine LoB, LoD, and LoQ during method validation and verification, especially for assays where low concentrations carry clinical weight — tumour markers, drugs, infectious targets. CLSI EP17 sets the study design for these claims; this calculator applies the parametric LoB and LoD formulas to the replicates you enter.
The calculator accepts 10 or more replicates of each; CLSI EP17 guidance uses about 60 blank and 60 low-level results to establish a limit and at least 20 to verify a claimed limit. Define the precision goal that sets the LoQ before collecting data. Distinguish detection from quantitation in reporting. For overall method spread, see measurement uncertainty and sigma metrics. Unsure which limit your claim needs? Our Test Selector can help.
Expected: 4 columns: Blank replicates | Low-level sample replicates | Calibration concentrations | Instrument responses
Drop a CSV here or click to choose. Parsed in your browser: nothing is uploaded.
Expected: 4 columns: Blank replicates | Low-level sample replicates | Calibration concentrations | Instrument responses
blank <- c({blank})
low <- c({low})
LoB <- mean(blank) + 1.645 * sd(blank)
cp <- 1.645 / (1 - 1 / (4 * (length(low) - 1)))
LoD <- LoB + cp * sd(low)
c(LoB = LoB, LoD = LoD)
# ICH Q2 calibration-curve alternative:
conc <- c({x}); resp <- c({y})
fit <- lm(resp ~ conc)
c(LoD = 3.3 * summary(fit)$sigma / coef(fit)[2], LoQ = 10 * summary(fit)$sigma / coef(fit)[2])User guide
When to use. Estimate the limit of blank and limit of detection from blank and low-level replicates with the parametric formulas (CLSI EP17-A2 sets the study design), or LoD/LoQ from a calibration curve (ICH Q2(R1)).
Assumptions. EP17: results are approximately Gaussian, from at least 60 blank and 60 low-level measurements (20 each to verify) spread over several days and reagent lots. ICH: linear response near the limit.
Common mistakes. The calculator accepts 10 or more replicates; EP17 guidance uses about 60 blank and 60 low-level results to establish a limit and at least 20 to verify a claimed limit. This parametric route assumes a single low-level sample; with several samples or non-Gaussian blanks use the non-parametric procedure. Confirm limits experimentally.
Worked example
Click Load example data above, then Run Analysis to see a fully worked result with figure, formula and interpretation for this test.
References
- CLSI. Evaluation of Detection Capability for Clinical Laboratory Measurement Procedures; EP17-A2. 2012.
- ICH Q2(R1). Validation of Analytical Procedures: Text and Methodology. 2005.
- Armbruster DA, Pry T. Limit of blank, limit of detection and limit of quantitation. Clin Biochem Rev. 2008;29(Suppl 1):S49-S52.
Worked Examples
Example 1 — From blanks to LoD
Replicate blank measurements give a limit of blank at the 95th percentile of the blank signal. Adding the variability of low-concentration samples to that LoB yields the limit of detection — the lowest concentration that produces a signal reliably above what a blank alone would give.
Example 2 — Setting the LoQ by precision
The limit of quantitation is the lowest concentration where imprecision meets a pre-set goal, say a CV of 20%. A concentration detected (above LoD) but with a CV of 35% is below the LoQ — present, but not measurable accurately enough to report a number.
Assumptions to Check
Adequate blank and low-level replicates. Stable LoB and LoD estimates require enough measurements of blank and low-concentration samples across runs and days.
A pre-defined precision (and bias) goal for LoQ. The LoQ depends on the acceptable imprecision; this goal must be set before the data are analysed.
Representative conditions. The samples and runs should reflect routine operation, including multiple reagent lots and operators where relevant.
Common Mistakes
Confusing LoD with LoQ
Detection is not quantitation. A concentration above the LoD may still be too imprecise to report a number; the LoQ is the threshold for reliable quantitation.
Too few replicates
Sparse blank or low-level data give unstable limits. Follow the protocol’s replication requirements for trustworthy claims.
Setting the LoQ goal after the fact
Choosing the acceptable CV after seeing the data biases the LoQ. Define the precision goal in advance.
Ignoring matrix and lot effects
Limits estimated under idealised conditions may not hold routinely; include realistic matrices, lots, and operators.
Frequently Asked Questions
What is the difference between LoB, LoD, and LoQ?
LoB is the highest blank signal expected, LoD is the lowest concentration reliably distinguished from a blank, and LoQ is the lowest concentration measurable with acceptable precision and accuracy.
Why report LoQ as well as LoD?
Because a result above the LoD may still be too imprecise to quantify; the LoQ marks where a numeric result can be trusted.
How is the LoQ goal chosen?
From the clinical precision requirement — commonly a target CV (and bias) that the assay must meet at the lowest reportable concentration.
Does the result match R?
Yes. The calculator applies LoB = mean of blanks + 1.645 SD and LoD = LoB + cp × SD of the low-level sample, and shows the R command so you can reproduce each limit.
Related Calculators
References
- Armbruster DA, Pry T. Limit of blank, limit of detection and limit of quantitation. Clin Biochem Rev. 2008;29(Suppl 1):S49–S52. PMID 18852857.
- Nikler A, Čičak H, Bejuk D, Radišić Biljak V, Šimundić AM. Verification of Atellica 1500 and comparison with Iris urine analyser and urine culture. Biochem Med (Zagreb). 2021;31(1):010701. PMID 34955669.
- CLSI. Evaluation of Detection Capability for Clinical Laboratory Measurement Procedures. EP17-A2. 2nd ed. Wayne, PA: Clinical and Laboratory Standards Institute; 2012.
Need This Analysis Done for Your Manuscript?
Our team supports assay validation — LoB, LoD, and LoQ determination per CLSI EP17 with the required replication and precision goals — with reproducible R output.
